Crawl Space Mold Removal in Encino, California

We dry the space, kill the mold, and keep it from coming back

Crawl Space Mold Removal in Encino, California starts with finding the moisture source, not just spraying the fungus. Our crew handles crawl space mold remediation Encino wide, from the flat lots near Encino Park to the hillside homes above Ventura Boulevard. If you smell that damp, musty odor every time the furnace kicks on, we can inspect today and tell you exactly what is growing under your floor.

A cleaner in protective coveralls and gloves vacuuming a modern living room.

Crawl Space Mold Removal in Encino, California

Crawl Space Mold Removal in Encino, California is the process of containing, removing, and disinfecting fungal growth from the unconditioned space beneath your home, then correcting the moisture that caused it. We set up 6 mil poly sheeting and a zipper door at the access hatch, run a negative air machine with HEPA filters, and remove contaminated insulation, joist paper, and debris. Surfaces get HEPA vacuuming, a sporicidal cleaner, and a mold encapsulant so spores cannot settle back into the wood.

Encino homes sit on raised foundations, and that open dirt underneath pulls moisture straight up into the floor framing all year. Add a drip line leak, a clogged French drain, or a washing machine hose that let go, and you have black mold growth on joists within a week. We see it constantly in Encino Village and South Encino, where 1950s ranch homes still have original subflooring and minimal vapor control. If you have been searching crawl space mold removal in Encino California and putting it off, the framing is not going to dry out on its own.

Why Encino Homeowners Remove Crawl Space Mold

Why Encino Homeowners Remove Crawl Space Mold

Mold under a house does not stay under the house. It rides the stack effect up through the floor, into the living room, and through the HVAC system. Here is what proper removal actually buys you.

Healthier Air Upstairs

Air in a crawl space rises. When we remove mold growth and seal the space, the musty smell and spore load in your bedrooms drops with it. Most clients notice the difference in the first 48 hours after we finish, especially in homes with HVAC returns running through the subfloor.

Stops Wood Rot Cold

Mold and wood rot travel together. Active growth means framing stays above 20 percent moisture, and joists, sill plates, and girders start losing strength. Removing the mold and drying the framing to under 15 percent stops the decay before a $12,000 structural repair becomes necessary.

Protects Your Insulation

Fiberglass batts between joists soak up spores and hold damp air against the wood. Once contaminated, they cannot be cleaned. We pull the ruined batts, bag them in the containment zone, and replace them after the framing is dry and treated, so you are not paying to heat a mold farm.

Ends the Odor Problem

That damp basement smell is microbial volatile compounds, not dirt. Wiping down joists with disinfectant wipes does nothing. We use a fogger and a sporicidal cleaner on every exposed surface, then verify with air sampling so the odor is gone at the source, not masked.

How Our Crawl Space Mold Removal Works

Every job follows the same five stages, whether it is a 900 square foot crawl space in Encino Terrace or a 3,000 square foot hillside home in Encino Hills. You get a written scope, a fixed price, and daily updates while we are on site.

1

Inspection and Testing

We crawl the whole space with a boroscope inspection camera and a thermal imaging camera to find hidden mold behind drywall and wet framing you cannot see from the hatch. A moisture meter maps the wet zones, and an air sampling pump collects spore counts for the lab. This takes 60 to 90 minutes and tells us exactly how far the contamination reaches.

2

Containment Setup

We seal the access hatch and any floor penetrations with 6 mil poly sheeting and containment tape, then install a zipper door so we can move in and out without spreading spores into your living space. A negative air machine with HEPA filters pulls the crawl space under negative pressure, so air flows in, never out. Setup runs about two hours.

3

Debris and Mold Removal

Contaminated insulation, cardboard, and fallen debris get bagged and hauled out. Joists and subfloor get HEPA vacuuming first, then dry ice blasting machine treatment on heavy growth, which lifts mold off wood without sanding or adding water. A sporicidal cleaner follows on every surface. This is the longest stage, usually one to three days depending on square footage.

4

Treatment and Encapsulation

We apply a mold encapsulant to lock down any remaining spores and protect the wood. A fogger pushes antimicrobial solution into corners, rim joists, and gaps a sprayer cannot reach. If you want vapor control, we install a heavy-duty liner across the dirt floor at this stage. Treatment and encapsulation take one day.

5

Verification and Handoff

A dehumidifier runs until framing moisture reads under 15 percent on the meter. We take post-remediation air samples and send them to the lab, then walk you through the results and the photos. If the numbers are clean, we pull containment and you get a written summary of everything we did.

Four Years of Crawl Space Work in the Valley

We have been removing crawl space mold since 2022, and in four years we have worked on hundreds of raised-foundation homes across the San Fernando Valley. Our technicians hold IICRC WRT and IICRC AMRT credentials, and our inspector carries ACAC CMI certification. Every job is scoped to ANSI/IICRC S520, the industry standard for mold remediation, and we follow ANSI/IICRC S500 when water damage is part of the picture. We are a licensed California contractor through the California Contractors State License Board, and we carry the insurance and OSHA 10 training that lets us work safely in confined spaces.

  • IICRC WRT and AMRT certified technicians on every crawl space job
  • ACAC CMI certified inspector handling all initial assessments
  • All scopes written to ANSI/IICRC S520 mold remediation standard
  • Licensed through the California Contractors State License Board
  • OSHA 10 confined space and respiratory protection training
Four Years of Crawl Space Work in the Valley

Why Encino Calls Us for Crawl Space Mold Removal

Plenty of companies will spray something under your house and hand you a bill. We find the water, fix the cause, remove the growth, and prove the result with lab numbers. Here is what that looks like in practice.

We Find the Water First

Mold removal without moisture correction is a callback waiting to happen. We trace every wet zone to its source, whether that is a failed supply line, a grading issue pushing runoff under the house, or a disconnected downspout. You get photos of the actual cause, not a guess.

Lab-Verified Results

We take air samples before and after every job and send them to an accredited lab. You see the spore counts drop in writing. If the post-remediation numbers do not meet the clearance criteria in ANSI/IICRC S520, we go back in and re-clean at no extra charge.

Dry Ice Blasting, Not Sanding

Sanding mold off joists is slow, messy, and can spread spores. Our dry ice blasting machine lifts growth off wood, concrete, and copper without abrasion or added moisture. It reaches into the grain and around fasteners where a wire brush cannot, and it leaves no secondary media to clean up.

Same-Day Response in Encino

Water in a crawl space gets worse by the hour. Call before noon and we can usually have a technician under your house the same day for crawl space mold removal in Encino California, including weekends. We serve Encino Hills, Amestoy Estates, and the Ventura Boulevard Corridor from the same dispatch.

What Crawl Space Mold Removal Includes

Every crawl space job we quote includes the full sequence from inspection through clearance testing. If your home needs vapor control, insulation replacement, or a plumbing repair, we will tell you upfront what that adds. Nothing gets discovered halfway through and billed later.

What's Included

Full Crawl Space Inspection

Thermal imaging camera and moisture meter readings on every joist, sill plate, and girder, plus a boroscope inspection camera for areas behind ductwork and plumbing. You get photos of everything we find and a written scope.

Containment and Negative Air

6 mil poly sheeting, containment tape, and a zipper door seal the access point. A negative air machine with HEPA filters keeps the crawl space under negative pressure so spores cannot migrate into your living space while we work.

Debris Removal and HEPA Vacuuming

Contaminated insulation, cardboard, and organic debris get bagged and hauled out. Every exposed surface then gets HEPA vacuuming to pull settled spores off the wood before any wet treatment is applied.

Dry Ice Blasting and Treatment

A dry ice blasting machine removes growth from framing, subfloor, and copper lines without sanding or water. A sporicidal cleaner and antimicrobial solution follow, then a mold encapsulant locks down the wood.

Fogging and Vapor Control

A fogger reaches rim joists and corners a sprayer cannot. If your crawl space has bare dirt, we install a heavy-duty liner to cut off the moisture vapor that started the problem in the first place.

Post Remediation Testing

Air sampling pump collection before and after, with lab analysis compared against an outdoor baseline. You get the clearance report in writing, and we do not call the job finished until the numbers meet ANSI/IICRC S520 criteria.

Crawl Space Problems We Fix in Encino

Most crawl space calls start with a smell, a soft floor, or a high utility bill. By the time a homeowner notices, the growth has usually been active for weeks. Here is what we run into most often.

Problem

Musty odor rising through the floor

That smell is microbial compounds from active growth, and it means spores are already migrating into your living space through every gap in the subfloor and around plumbing penetrations.

Solution

We locate the growth with a thermal imaging camera and moisture meter, remove it under containment, and treat the framing with a sporicidal cleaner and fogger. Air sampling before and after proves the spore load dropped.

Problem

Black mold growth on floor joists

Black mold on joists means wood moisture has been above 20 percent long enough for colonization. Left alone, the same conditions feed wood rot fungi that weaken structural framing.

Solution

We HEPA vacuum the joists, run a dry ice blasting machine over the growth, and apply a mold encapsulant. Then we correct the moisture source so the wood dries below 15 percent and stays there.

Problem

Wet insulation holding damp against wood

Fiberglass batts between joists act like a sponge. Once they take on water and spores, they hold moisture against the framing and cannot be cleaned, only replaced.

Solution

We pull the contaminated batts inside the containment zone, bag them, and haul them out. New insulation goes in only after the framing is dry and treated, so you are not reinstalling a problem.

Problem

Standing water after winter rains

Pooled water under a raised foundation pushes relative humidity past 80 percent and can wick several feet up into the framing within days. This is the fastest route to widespread crawl space mold.

Solution

We extract the standing water, run a dehumidifier until framing reads dry, then trace the entry point. Grading corrections, downspout extensions, and a vapor barrier keep the next storm from repeating it.

When Encino Homeowners Call Us

1

A 1950s ranch home in South Encino with original subflooring and a persistent damp smell in the hallway.

Solution:

We inspect with a boroscope inspection camera and moisture meter, find growth across roughly 60 feet of joists, and set containment the same day. Dry ice blasting removes the growth, and we install a vapor barrier over the bare dirt.

Outcome:

Framing moisture drops from 22 percent to 10 percent, air samples clear, and the hallway smell is gone within two days of completion.

2

A hillside home in Encino Hills where winter runoff has been seeping under the foundation for two seasons.

Solution:

We extract standing water, dry the space with a dehumidifier and air scrubber, then remove mold from the girder and sill plates. We also correct the grading and extend the downspouts that were dumping water at the foundation line.

Outcome:

The crawl space stays dry through the following rainy season, and the homeowner avoids a girder replacement that would have run past $14,000.

3

A duplex near the Ventura Boulevard Corridor where a tenant reported a musty smell and the landlord needed documentation for insurance.

Solution:

We run air sampling pump tests in both units and the crawl space, document the growth with photos and moisture readings, and complete remediation under containment. Full lab reports go to the owner for the claim.

Outcome:

The carrier approves the claim based on the documentation, and both units pass post remediation mold testing on the first clearance round.

4

A home in Amestoy Estates where a water heater failure sent 40 gallons across the subfloor.

Solution:

We handle water damage mold remediation in sequence: extraction and drying to ANSI/IICRC S500 standards first, then mold removal on the framing that stayed wet too long. New insulation goes in after clearance.

Outcome:

Drying first cut the removal scope by about a third, and the homeowner saved roughly $2,000 compared to remediating the whole space.

Tools and Methods We Use

Tools & Equipment

Thermal Imaging Camera

Reveals temperature differences that point to hidden moisture behind framing and under subflooring, so we find wet zones before mold becomes visible.

Moisture Meter

Gives us exact wood moisture readings on joists, sill plates, and girders. We use it to set the drying goal and to confirm framing is below 15 percent before we close out.

Boroscope Inspection Camera

Slides into gaps behind ductwork, plumbing chases, and rim joists where a flashlight cannot reach, so nothing gets missed during the inspection.

Negative Air Machine and Air Scrubber

Keeps the crawl space under negative pressure and filters airborne spores through HEPA filters, protecting your living space while we work.

Dry Ice Blasting Machine

Lifts mold off wood, concrete, and copper using dry ice pellets. No sanding, no added water, and no secondary media left behind in the crawl space.

Fogger and Dehumidifier

The fogger pushes antimicrobial solution into corners and rim joists a sprayer misses. The dehumidifier pulls moisture out of the framing until it reads dry.

Air Sampling Pump

Collects calibrated air samples before and after remediation so an accredited lab can compare spore counts against an outdoor baseline.

Methods

ANSI/IICRC S520 Mold Remediation Standard

This is the industry standard that governs containment, removal, and clearance. Every scope we write follows it, which is why our post-remediation testing results hold up with insurers and home inspectors.

ANSI/IICRC S500 Water Damage Standard

When a leak or flood is part of the picture, we dry the structure to S500 standards before removing mold. Drying first shrinks the removal scope and saves you money on the back end.

HEPA Vacuuming Before Wet Treatment

Settled spores have to come off the wood before any liquid touches it. HEPA vacuuming first prevents the smearing that happens when cleaners are applied directly to dry growth.

Encapsulation and Vapor Control

A mold encapsulant seals treated wood, and a heavy-duty liner over bare dirt cuts off the moisture vapor that feeds growth. Together they are what keeps the crawl space from reverting.

Post Remediation Clearance Testing

We do not declare a job finished on visual inspection alone. Air samples go to an accredited lab, and the numbers have to meet clearance criteria before we pull containment.

How Crawl Space Mold Removal Runs in Encino

Encino sits in a warm, dry part of the San Fernando Valley, which fools a lot of homeowners into thinking crawl space mold is not a local problem. It is. Most of the housing stock here is raised-foundation construction from the 1940s through the 1960s, and those crawl spaces were built with bare dirt floors and minimal ventilation. During the wet months, that dirt releases water vapor straight into the subfloor framing, and relative humidity under the house regularly climbs past 70 percent. Add the clay-heavy soil common in Encino Hills and Royal Oaks, which sheds runoff instead of absorbing it, and you get water pooling at foundation lines after every significant storm. We see the worst growth in Encino Village and South Encino, where original subflooring has been absorbing that moisture for decades. Our approach is to dry the framing first, remove the growth under containment, then install vapor control and correct the drainage that let the water in. If you have been putting off crawl space mold treatment Encino California because the space is hard to access, we handle the crawl for you and bring back photos of everything we find. Homes near Encino Park and along the Sepulveda Boulevard Corridor often need grading corrections in addition to remediation, since runoff from neighboring lots drains toward their foundations.

Service Areas

Encino Village

Dense block of 1950s ranch homes with original subflooring and bare dirt crawl spaces. This is where we find the most advanced growth, often across 50 feet or more of joists.

Encino Hills

Sloped lots with clay soil that pushes storm runoff toward foundations. Grading corrections and downspout extensions are usually part of the scope here.

South Encino

Older raised-foundation homes with limited crawl space ventilation. We frequently add vapor barriers and ventilation improvements alongside mold removal.

Royal Oaks

Larger homes with deeper crawl spaces and more plumbing runs, which means more chances for a slow supply line leak to go unnoticed for weeks.

Encino Terrace

Mix of original homes and remodels. Renovations sometimes seal off crawl space vents, trapping moisture and triggering growth after the first wet season.

Local Considerations

Bare dirt crawl space floors releasing vapor year round

Relative humidity under the house climbs past 70 percent during wet months, keeping framing above 20 percent moisture and feeding active mold growth. A heavy-duty liner cuts the vapor off at the source.

Clay-heavy soil in the hills shedding storm runoff

Water pools at foundation lines instead of soaking in, which is why Encino Hills and Royal Oaks homes often need grading and drainage work alongside remediation.

Original 1950s subflooring with decades of moisture exposure

Older wood holds moisture longer and shows deeper growth. Dry ice blasting removes it without sanding away the surface, which matters when framing is already aged.

Sealed or blocked crawl space vents after remodels

Without airflow, trapped moisture has nowhere to go. We restore ventilation as part of the scope so the space can dry between storms.

Encino Village Ranch Home, 60 Feet of Joists

Before

A 1954 ranch home with a damp smell in the hallway and soft spots near the bathroom. Inspection found black mold growth across roughly 60 feet of joists, with framing moisture at 22 percent and ruined insulation batts throughout.

After

Containment went up the same day. Dry ice blasting removed the growth, a sporicidal cleaner and encapsulant followed, and new insulation went in after the framing dried. Post-remediation air samples cleared on the first round, and framing moisture read 10 percent.

Maintenance & Follow-up

We installed a vapor barrier over the bare dirt and extended two downspouts away from the foundation. Checking the crawl space once each fall keeps it that way.

Before

Storm runoff had been seeping under the foundation for two winters. Standing water sat against the girder and sill plates, and the homeowner had started noticing a musty odor in the living room and a soft spot near the fireplace.

After

We extracted the standing water, dried the space with a dehumidifier and air scrubber, then removed mold from the girder and sill plates with HEPA vacuuming and dry ice blasting. Framing moisture dropped from 26 percent to 11 percent.

Maintenance & Follow-up

Grading was corrected and downspouts extended past the foundation line. The crawl space stayed dry through the next rainy season, and the homeowner avoided a girder replacement quoted at over $14,000.

Before

A tenant reported a musty smell, and the landlord needed documentation for an insurance claim. Both units and the crawl space showed elevated spore counts, with visible growth on the subfloor beneath the shared bathroom.

After

We ran air sampling pump tests in both units and the crawl space, documented everything with photos and moisture readings, and completed remediation under containment. Both units passed post remediation mold testing on the first clearance round.

Maintenance & Follow-up

The owner now schedules an annual crawl space check before the wet season. Catching a slow leak early is far cheaper than a second remediation.

Frequently Asked Questions

Have questions? We have answers.

Call Us
How much does crawl space mold removal cost in Encino California?

Most crawl space jobs in Encino run $1,800 to $6,500 in 2026, with small single-source cleanups starting near $1,200 and full encapsulation projects reaching $9,000 or more. Square footage drives most of it, followed by how much insulation has to be replaced and whether dry ice blasting is needed. We quote a fixed price after the inspection, so you are not guessing.

What causes crawl space mold in Encino?

Moisture, always. Encino sits on raised foundations over bare dirt, and that soil releases water vapor into the framing year round. Add a plumbing leak, poor grading, a clogged drain, or a roof leak that runs down inside the walls, and relative humidity under the floor climbs past 60 percent. Once wood moisture stays above 20 percent for a few days, mold growth starts.

Can crawl space mold remediation prevent wood rot in Encino, California?

Yes, if the moisture is corrected at the same time. Mold needs sustained damp conditions, and rot fungi need the same thing. When we dry framing below 15 percent moisture and install vapor control, the wood stops decaying. We check joists, sill plates, and girders with a moisture meter during the inspection and flag any structural loss before it becomes a repair bill.

Is crawl space mold removal covered by insurance in Encino?

It depends on the cause. Sudden events like a burst supply line or a water heater failure are often covered, while long-term humidity and gradual leaks usually are not. We document everything with photos, moisture readings, and lab results so you have what the adjuster needs. Call us at (833) 929-5837 and we will walk you through what to send your carrier.

Licensed, Certified, and Verified

Certifications

IICRC WRT (Water Damage Restoration Technician) by Institute of Inspection, Cleaning and Restoration Certification
IICRC AMRT (Applied Microbial Remediation Technician) by Institute of Inspection, Cleaning and Restoration Certification
ACAC CMI (Certified Mold Inspector) by American Council for Accredited Certification
California Contractors State License Board by State of California
OSHA 10 Confined Space Training by Occupational Safety and Health Administration

Reviews

Google

They found a leak we did not know about and showed us photos of the mold before they started. Containment was sealed tight, and the dry ice blasting left the joists looking clean. Lab results came back clear on the first try. Fair price for the amount of work.

Yelp

Called on a Tuesday about a musty smell, had a technician under the house Wednesday morning. They mapped the whole crawl space with a moisture meter and gave us a fixed quote the same day. Three days of work and the smell is completely gone.

BBB

We needed documentation for an insurance claim and they delivered everything the adjuster asked for, including before and after air samples. Professional crew, clean work, and they explained each step without overselling anything.

Google

Our Encino Hills home had water under it after the winter storms. They dried it out first, which saved us money on the mold removal, then corrected the grading so it would not happen again. Honest about what was needed and what was not.

Related Services

Mold Inspection Near Me

Before any crawl space work starts, we inspect the whole house. Attic, bathrooms, and HVAC closets get checked too, because mold under the floor often has company upstairs. The inspection report tells you what is growing and where.

Mold Inspection Near Me

Mold Inspection

A full mold inspection covers the crawl space, attic, and living areas with thermal imaging and moisture readings. For Encino homes with raised foundations, the crawl space is usually where the worst growth hides, so we spend most of the visit down there.

Mold Inspection

Mold Testing

Lab testing confirms what is growing and how much. We collect air and surface samples from the crawl space and compare them to an outdoor baseline, which is how we prove whether the growth is active or old and dormant.

Mold Testing

Mold Testing Near Me

If you are in Encino and need same-week testing, we run air sampling pumps and surface swabs, then send results to an accredited lab. Crawl space samples usually come back in two to three business days.

Mold Testing Near Me

Certified Mold Inspector

Our inspector holds ACAC CMI certification and writes scopes to ANSI/IICRC S520. That matters in a crawl space, where the difference between surface staining and active growth changes the whole remediation plan.

Certified Mold Inspector

Black Mold Inspection

Black mold growth on crawl space joists is common in older Encino homes. We identify it under containment, sample it, and remove it with HEPA vacuuming and dry ice blasting rather than sanding it into the air.

Black Mold Inspection

Home Mold Inspection

A whole-home inspection ties the crawl space to everything above it. We check for attic mold from roof leaks, bathroom mold, and HVAC mold contamination, then rank the findings so you know what to fix first.

Home Mold Inspection

Residential Mold Testing

Residential testing for Encino homeowners includes crawl space air samples, surface samples from visible growth, and a written report with spore counts. It is the baseline we use to prove remediation worked.

Residential Mold Testing

Commercial Mold Inspection

Commercial buildings on Ventura Boulevard with raised foundations get the same crawl space attention, plus HVAC and tenant-space checks. We schedule after hours so your business keeps running.

Commercial Mold Inspection

Mold Remediation Company

We are a licensed California contractor handling containment, removal, treatment, and clearance testing in house. No subcontractors, no handoffs, and one point of contact from inspection through final air samples.

Mold Remediation Company

Emergency Mold Testing Services

When a pipe lets go under the house, testing needs to happen fast. We can be under your floor the same day to map the wet zone and start drying before mold growth establishes itself.

Emergency Mold Testing Services

Same Day Mold Testing

Call before noon and we can usually sample the crawl space the same day. Results come from the lab in two to three business days, and we review them with you over the phone.

Same Day Mold Testing

Basement Mold Inspection

Homes with basements and below-grade rooms get the same moisture mapping we use in crawl spaces. We check wall framing, floor joists, and any storage areas holding damp air against wood.

Basement Mold Inspection

Attic Mold Testing And Removal

Attic mold from roof leaks often shows up alongside crawl space growth. We test and remove it with the same containment and HEPA methods, then correct the leak that fed it.

Attic Mold Testing And Removal

Air Quality And Mold Testing

Air quality testing measures what you are breathing. We sample the crawl space, the living space, and outdoor air, then compare the numbers so you know whether spores are migrating upstairs.

Air Quality And Mold Testing

Mold Remediation Near Me

If you are searching from Encino Hills or Royal Oaks, we are minutes away. Our crews work the whole San Fernando Valley and can usually inspect within 24 hours of your call.

Mold Remediation Near Me

Bathroom Mold Removal Service

Bathroom mold usually traces back to a failed caulk line or a slow drain leak. We remove the growth, treat the framing, and fix the moisture source so it does not return.

Bathroom Mold Removal Service

Toxic Mold Removal

When sampling identifies toxigenic species, we upgrade containment and respiratory protection and follow ANSI/IICRC S520 protocols for the higher risk category. Clearance testing is mandatory before we pull containment.

Toxic Mold Removal

Mold Abatement

Abatement covers the physical removal of mold-contaminated materials under containment. In a crawl space that means bagging ruined insulation, HEPA vacuuming framing, and treating every exposed surface.

Mold Abatement

Professional Mold Removal

Professional removal means containment, negative air, HEPA filtration, and lab verification. It is the difference between mold that stays gone and mold that comes back in six weeks.

Professional Mold Removal

Mold Cleanup Near Me

Cleanup after a leak or flood in Encino starts with water extraction and drying, then moves to mold removal once the framing is stable. We handle both stages with the same crew.

Mold Cleanup Near Me

Water Damage Mold Remediation

Water damage and mold go together. We dry the structure to ANSI/IICRC S500 standards, then remediate any growth that already started. Drying first saves money on the removal scope.

Water Damage Mold Remediation

Mold Spore Testing

Spore testing gives you a number, not an opinion. We collect air samples with a calibrated pump and compare indoor counts to outdoor baselines, which is how clearance is determined.

Mold Spore Testing

Post Remediation Mold Testing

After removal, we sample again to confirm the crawl space meets clearance criteria. If the numbers are high, we re-clean before we call the job done. You get the lab report in writing.

Post Remediation Mold Testing

Mold Fogging Treatment

A fogger pushes antimicrobial solution into rim joists, corners, and gaps a sprayer misses. It is the finishing step after physical removal, not a replacement for it.

Mold Fogging Treatment

Dry Ice Blasting Mold

Dry ice pellets lift mold off joists, subfloor, and copper without sanding or water. It is the cleanest way to remove growth from crawl space framing, and it leaves no media behind.

Dry Ice Blasting Mold

Affordable Mold Remediation

Affordable does not mean skipping containment. We scope the job to what is actually contaminated, replace only the insulation that is ruined, and give you a fixed price before we start.

Affordable Mold Remediation

24 Hour Mold Removal

Water under a house does not wait for business hours. We take emergency calls around the clock for active leaks and standing water in crawl spaces across Encino and the Valley.

24 Hour Mold Removal

Odor Removal Mold

Musty odors come from microbial compounds in the growth itself. Removing the mold and treating the framing eliminates the smell at the source. Air fresheners and ozone machines only mask it.

Odor Removal Mold

Get Crawl Space Mold Removal in Encino, California

We are licensed through the California Contractors State License Board and every job ends with lab-verified clearance. Call (833) 929-5837 and we will schedule an inspection, usually within 24 hours. If there is water under your floor right now, say so on the call and we will treat it as an emergency.